View Products
-
10ft Shielded SVGA Cable with 3.5mm Audio Double Shielded
$17.95 10H1-29110Our 10 foot black HD15 video cable with a 3.5mm Stereo Audio cable built in, more commonly referred to as a SVGA male to male cable with audio, is typically used to connect a computer to a computer monitor. Our SVGA video cables can handle the lowest resolutions used on computer monitors today all the way up to a maximum of 2048 x 1536. Plus this cable is double shielded to extend your video and audio signals without distortion or signal loss.Part No. 10H1-29110 -
10ft Slim SVGA Cable with Ferrite Beads HD15 Male 32 AWG
$18.95 10H1-11110Our 10 foot black Slim HD15 video cable, more commonly referred to as a SVGA male to male cable, is typically used to connect a computer to a computer monitor. This specific cable is a slim version, composed of 32 AWG (American Wire Gauge) coaxial wires, which is easier to route and manage. Ferrite Cores are small magnetic cores wrapped around the ends of the cable. They are used to suppress EMI/RFI electronic noise on the cable by absorbing the unwanted high frequencies and dissipating them. Slim SVGA Monitor Cables are smaller diameter than normal SVGA cables. Slim SVGA Cables also have a smaller hood and ferrite's to fit where other SVGA Cables will not. Our SVGA video cables can handle the lowest resolutions used on computer monitors today all the way up to a maximum of 2048 x 1536.Part No. 10H1-11110 -
10ft SVGA Cable HD15 Male to Male Ferrite Core
$15.95 10H1-20110This 10 foot black SVGA Cable has two HD15 male ends and features ferrite beads, coaxial construction and double shielding. Its primary use is for connecting a computer to a computer monitor for video display. The ferrite beads/cores are small iron oxide alloy cylinders wrapped around the ends of the cable. They are used to suppress EMI/RFI electronic noise on the cable by absorbing the unwanted high frequencies and dissipating them. The coaxial construction and double shielding work to further suppress noise, delivering you the best picture possible. Our SVGA video cables can handle the lowest resolutions used on computer monitors today all the way up to a maximum of 2048 x 1536.Part No. 10H1-20110 -
10ft SVGA Extension Cable, HD15 Male to Female
$17.95 10H1-20210This 10 foot black SVGA extension cable has a HD15 male and a HD15 female end. The cable features ferrite beads, coaxial construction and double shielding. Its primary use is for extending the length of a computer to computer monitor connection for video display. The ferrite beads/cores are small iron oxide alloy cylinders wrapped around the ends of the cable. They are used to suppress EMI/RFI electronic noise on the cable by absorbing the unwanted high frequencies and dissipating them. The coaxial construction and double shielding work to further suppress noise, delivering you the best picture possible. Our SVGA video extension cables can handle the lowest resolutions used on computer monitors today all the way up to a maximum of 2048 x 1536.Part No. 10H1-20210 -
10ft USB 2.0 Extension Cable Type A Male to Female
$3.95 10U2-02110EThis 10 foot USB extension cable will extend a standard USB 2.0 cable with a type-A connector. USB 2.0 cables are backwards compatible as they can carry a USB 1.0 and 1.1 signal. USB cables are used to connect devices such as digital cameras, digital video cameras, scanners, printers, web cams, mice, keyboards, joysticks, network connections, etc. The maximum length for a single USB cable is 15 feet. To get more than 15 feet you will need to boost the signal with a repeater Cable (Parts: UC-50200, UC-50500, 11U2-51032 or 11U2-51049) or Hub (Parts: 40U2-14260, 41U2-02707, 41U2-21700 or 41U2-22100).Part No. 10U2-02110E -
10ft USB 2.0 Printer Cable, Type A to B
$4.95 10U2-02210This is a 10 foot male to male USB 2.0 cable with one A-type connection and one B-type. These are more commonly known as USB Printer/Scanner/ Device Cables. Type A is typically the style of connection found on the backs of PCs. Type B is the smaller square connector typically found on devices such as: printers; scanners; external hard drives and USB hubs. USB 2.0 cables are backwards compatible as they can carry a USB 1.0 and 1.1 signal. The maximum length for a single USB cable is 15 feet. To get more than 15 feet you will need to boost the signal with a repeater Cable (Parts: UC-50200, UC-50500, 11U2-51032 or 11U2-51049) or Hub (Parts: 40U2-14260, 41U2-02707, 41U2-21700 or 41U2-22100).Part No. 10U2-02210 -
10ft USB 2.0 Type A Male to A Male Cable
$4.95 10U2-02110This is a 10 foot male to male USB 2.0 cable with A-type male connections on both ends. This is typically the style of connection found on the backs of PCs. This is not the standard configuration for a USB cable. Please make sure the device you are connecting to requires a Type A male cable, the port should be a type A female. USB 2.0 cables are backwards compatible, they can carry a USB 1.0 and 1.1 signal. USB cables are used to connect devices such as digital cameras, digital video cameras, scanners, printers, web cams, mice, keyboards, joysticks, network connections, etc.Part No. 10U2-02110 -
10ft USB 3.0 Cable Black Type A to Type A Male/Male
$6.95 10U3-02110BKOur black 10 foot USB 3.0 SuperSpeed Type A to Type A Male/Male Cables offer the next great leap in data transfer speeds for your devices that require a male A connection. Some routers and USB hard drives use these type of cables. The 3.0 specification boasts amazing performance improvements that will allow consumers and businesses to get more done in less time, while still supplying full backwards compatibility with previous USB versions. USB 3.0 SuperSpeed features a 10 fold improvement in signaling rate that translates to 5 Gbps versus the older 480 Mbps (USB 2.0). The new Sync-N-Go technology which minimizes user wait time (devices detect and sync faster). USB 3.0 is bi-directional allowing information transfers in both directions at the same time. Add to this the new support for a new interrupt driven protocol, the device can initiate the transfer, vs the old host based device polling. The old way had the USB controller constantly pinging the device, now the device lets the host know when actions start. Lastly USB 3.0 increases power output from 500 mA to 900 mA for faster charging of attached devices and support of more robust peripherals.Part No. 10U3-02110BK -
10ft USB 3.0 Cable Blue Type A to Type A Male/Male
$12.95 10U3-02110Our blue 10 foot USB 3.0 SuperSpeed Type A to Type A Male/Male Cables offer the next great leap in data transfer speeds for your devices that require a male A connection. Some routers and USB hard drives use these type of cables. The 3.0 specification boasts amazing performance improvements that will allow consumers and businesses to get more done in less time, while still supplying full backwards compatibility with previous USB versions. USB 3.0 SuperSpeed features a 10 fold improvement in signaling rate that translates to 5 Gbps versus the older 480 Mbps (USB 2.0). The new Sync-N-Go technology which minimizes user wait time (devices detect and sync faster). USB 3.0 is bi-directional allowing information transfers in both directions at the same time. Add to this the new support for a new interrupt driven protocol, the device can initiate the transfer, vs the old host based device polling. The old way had the USB controller constantly pinging the device, now the device lets the host know when actions start. Lastly USB 3.0 increases power output from 500 mA to 900 mA for faster charging of attached devices and support of more robust peripherals.Part No. 10U3-02110 -
10ft USB 3.0 Extension Cable Black Type A Male/Female
$6.95 10U3-02110EBKOur black 10 foot USB 3.0 SuperSpeed extension cables offer the next great leap in data transfer speeds for your devices. These particular USB 3.0 cables feature a Type A Male (Computer/Tablet/Laptop/Hub side) to Type A Female (Device side with Type A Male ended cable). This USB SuperSpeed cable enables the extension of an existing device up to a total of 10 feet without a hub/repeater or up to 60 feet (six cables) with hubs/repeaters. The 3.0 specification boasts amazing performance improvements that will allow consumers and businesses to get more done in less time, while still supplying full backwards compatibility with previous USB versions. USB 3.0 SuperSpeed features a 10 fold improvement in signaling rate that translates to 5 Gbps versus the older 480 Mbps (USB 2.0). The new Sync-N-Go technology which minimizes user wait time (devices detect and sync faster). USB 3.0 is bi-directional allowing information transfers in both directions at the same time. Add to this the new support for a new interrupt driven protocol, the device can initiate the transfer, vs the old host based device polling. The old way had the USB controller constantly pinging the device, now the device lets the host know when actions start. Lastly USB 3.0 increases power output from 500 mA to 900 mA for faster charging of attached devices and support of more robust peripherals.Part No. 10U3-02110EBK -
10ft USB 3.0 Extension Cable Blue Type A Male/Female
$13.95 10U3-02110EOur blue 10 foot USB 3.0 SuperSpeed extension cables offer the next great leap in data transfer speeds for your devices. These particular USB 3.0 cables feature a Type A Male (Computer/Tablet/Laptop/Hub side) to Type A Female (Device side with Type A Male ended cable). This USB SuperSpeed cable enables the extension of an existing device up to a total of 10 feet without a hub/repeater or up to 60 feet (six cables) with hubs/repeaters. The 3.0 specification boasts amazing performance improvements that will allow consumers and businesses to get more done in less time, while still supplying full backwards compatibility with previous USB versions. USB 3.0 SuperSpeed features a 10 fold improvement in signaling rate that translates to 5 Gbps versus the older 480 Mbps (USB 2.0). The new Sync-N-Go technology which minimizes user wait time (devices detect and sync faster). USB 3.0 is bi-directional allowing information transfers in both directions at the same time. Add to this the new support for a new interrupt driven protocol, the device can initiate the transfer, vs the old host based device polling. The old way had the USB controller constantly pinging the device, now the device lets the host know when actions start. Lastly USB 3.0 increases power output from 500 mA to 900 mA for faster charging of attached devices and support of more robust peripherals.Part No. 10U3-02110E -
10ft XLR Audio Cable XLR Female to 1/4 Inch Mono Male
$7.95 10XR-01510Our 10 foot 3-Pin XLR Female to 1/4 Inch Mono Male Audio Cables are built with high quality XLR and 1/4 inch connectors and audio cable for maximum signal transfer and RF/EMI noise resistance. The high density shield blocks electrostatic noise, eliminating annoying hum, buzz, radio interference and noise.Part No. 10XR-01510 -
10ft XLR Audio Cable XLR Female to 1/4 Inch Stereo Male
$9.95 10XR-01610Our 10 foot 3-Pin XLR Female to 1/4 Inch Stereo Male Audio Cables are built with high quality XLR and 1/4 inch connectors and audio cable for maximum signal transfer and RF/EMI noise resistance. The high density shield blocks electrostatic noise, eliminating annoying hum, buzz, radio interference and noise.Part No. 10XR-01610 -
10ft XLR Audio Cable XLR Male to XLR Female
$7.95 10XR-01210Our 10 foot 3-Pin XLR Audio Cables are built with high quality XLR connectors and audio cable for maximum signal transfer and RF/EMI noise resistance. The high density shield blocks electrostatic noise, eliminating annoying hum, buzz, radio interference and noise.Part No. 10XR-01210 -
Comzon® 10K/8K/4K 48Gbps Ultra-High-Speed Certified HDMI Cable, 4K120 / 8K60 / 10K, HDMI-A Male, Silver & Black woven jacket, 1 meter -
Comzon® 10K/8K/4K 48Gbps Ultra-High-Speed Certified HDMI Cable, 4K120 / 8K60 / 10K, HDMI-A Male, Silver & Black woven jacket, 2 meter -
Comzon® 10K/8K/4K 48Gbps Ultra-High-Speed Certified HDMI Cable, 4K120 / 8K60 / 10K, HDMI-A Male, Silver & Black woven jacket, 3 meter -
10m 10Gb Aqua LC Multimode Duplex Fiber Optic Cable, 50/125
$13.95 LCLC-31010This Aqua Blue jacketed 10 meter (~33 feet) 10 gigabit rated fiber optic cable is terminated with LC (Lucent Connector) connectors on both ends. It is a multimode fiber (50 micron core) designed to transmit data across shorter distances at LAN speeds. The cord is duplex (two fibers) which means it permits synchronous communication between devices. The cladding diameter is 125 microns. (Not for Home Theater)Part No. LCLC-31010 -
- High-performance audio cable for connecting Hi-Fi separates, audio, and home cinema equipment
- Delivers superb clarity, definition and detail
- Connectors: 2 x Phono Male to 2 x Phono Male
- Gold-plated connectors for excellent signal transfer
- 75 Ohm Pure Crystal Oxygen Free Copper (PC-OFC) coaxial conductor
- OFC braid with Aluminium Mylar foil wrap provides improved shielding
- 25 year warranty
Part No. 37524 -
- Ideal for use as a replacement phono lead for hi-fi's and music equipment etc.
- 2 x Phono Male to 2 x Phono Male
- Moulded, Gold Plated Connectors
- Cable Color: Black
- 10 year warranty
Part No. 35474 -
- 3.5mm Stereo Jack Male to 2 x Phono Male
- Moulded, Gold Plated Connectors
- Cable Color: Black
- 10 year warranty
Part No. 35494 -
- 3.5mm Stereo Jack Male to 3.5mm Stereo Jack Male
- Moulded, Gold Plated Connectors
- Cable Color: Black
- 10 year warranty
Part No. 35455 -
- 2 x Phono Male to 2 x Phono Female
- Moulded, Gold Plated Connectors
- Cable Color: Black
- 10 year warranty
Part No. 35484 -
- 3.5mm Stereo Jack Male to 3.5mm Stereo Jack Female
- Moulded, Gold Plated Connectors
- Cable Color: Black
- 10 year warranty
Part No. 35465
Our Featured Products
Select options
This product has multiple variants. The options may be chosen on the product page
Details
